The "suitcase"™ Mod by Project Sub-Ohm Is NOW LIVE!
Welcome The Little Brother Of the "littlemaN"™! Project Sub-Ohm™ Has Created The "suitcase"™ 50 Watts Mod!
WARNING!!! FOR USE WITH 30 AMPS OR HIGHER IMR BATTERIES ONLY!
NOTE: We decided to do things a little differently this time, so all serial numbers on "suitcase"™ are reverse serialized! Starting from 1000, 999, 998 and so on.
***This Listing Is For "suitcase"™ Mod Only!
Made By Pioneer4you X Project Sub-Ohm™
Even since the introduction of the "littlemaN'™ Box mod, the "littlemaN"™ has gain a huge popularity among the world of vapers! Now Project Sub-Ohm™ has found a perfect platform to build on its second box mod. The "suitcase"™ 50 Watts iPV2 Mod made by Pioneer4you. The goal is simple, to create an affordable yet still very powerful device that can satisfy majority of the vapers out there!
Product Includes:
1 "suitcase"™ Mod by Project Sub-Ohm™
1 USB Cord
Product Descriptions:
The "suitcase"™ series by Project Sub-Ohm™ is a powerful Variable Wattage Device that can adjustable it's power from 7W to 50W in increments of 0.1 Watts! This device uses upgraded YiHi SX330 Chip, which is capable of firing coils at 0.2 ohm up to 3.0 ohm. The "suitcase"™ Mod is powered by a single IMR 18650 battery and is capable of producing up to 50 Watts of power! The two screws on the back of the device hold the battery cover firm and sturdy. The battery is removable, but the device can also be charged internally with the included USB to Micro USB cord. The device can also act as a passthrough while charging, super handy when you need to vape while charging. The OLED screen is bright and easy to read, and also shows you the wattage, resistance, output voltage and battery life. There are two ways of firing the device, a standard firing button and a revolutionary "Touch Firing", which is located next the the 510 connection. This sensor allows the device to be fired using heat from your finger when press on to the plate.
Product Features:
Full Aluminum Body For rigidity!
Capable of firing 0.2 ohm - 3.0 ohm build
Capable of putting out 50 Watts of power!
Beautifully Engraved With Project Sub-Ohm™ Logo and "suitcase"™ logo
Serialized (Reverse serialized starting from 1000, 999, 998 and so on)
Matches all other Project Sub-Ohm™ products
Product Specs:
Output Power: 7W - 50W
Output Voltage: 3.6V - 8.5V
Input Current: 1.3A - 20A
Input Voltage: 3.2V - 4.5V
Loading Resistance: 0.2 ohm - 3.0 ohm
Low Resistance Protection
High Input Voltage Warning
Output Short Circuit Protection
Reverse Battery Protection
Product Recommendations:
FOR USE WITH 30 AMPS OR HIGHER IMR BATTERIES ONLY!
Please do not put in your battery in wrong direction
Make sure battery sit completely snug in the battery slot
Do not use any batteries if the outside wrapper has come off!
Turn off the device before pulling your battery out
Do not wrap your coils below 0.2 ohm and always vape safe!
Warning: Project Sub-Ohm™ is a product design and development studio for Electronic Cigarettes and do not involve in any product manufacturing process. Use this product at your own risk. In no event, regardless of cause shall VaporDNA™ and Project Sub-Ohm™ be liable for any type of bodily injury or property damage.
***Always turn off the device and take the battery out when not in use!
Advanced User Item. Use AT YOUR OWN RISK!
FOR USE WITH 30 AMPS OR HIGHER IMR BATTERIES ONLY!!!
Project Sub-Ohm™ is a sub-division of VaporDNA™.
All pictures are based on practicality, copyright reserved.
Сообщение от elevated
Вот с байкой. Телефон такой телефон...
Ваши права
Начинающий парильщик. Не курю с 01.09.2012. и пока не тянет. 
