Specifications
Temperature Protection
The DNA 40 is the first power supply for electronic cigarettes to directly measure and limit the
temperature of the heating coil during operation. By preventing the coil from becoming too hot
regardless of fluid, wicking or airflow, a variety of undesirable situations can be prevented. For example,
appropriate temperature settings will prevent the wicking material from charring, which compromises
taste and introduces unintended chemicals into the vapor. Appropriate temperature settings will also
reduce the breakdown of flavoring and base liquid components, which could impact taste or safety.
Evolv’s Temperature Protection Technology requires a heating coil made from Nickel 200 alloy,
rather than Nickel Chromium or Kanthal alloys. Nickel 200 is commercially pure nickel. It is often sold in
vapor shops and online as “non-resistance wire.” If the temperature reaches the maximum value, the
wattage applied to the atomizer coil is reduced to prevent overheating. Please note that the
temperature reading is the average temperature of the atomizer coil, and care should be taken to
construct the heating coil so that the temperature is uniform, without hot or cold spots. Ensure that the
coil does not short to itself.
Because wattage, not temperature controls vapor volume, large vapor volumes can be produced
without unnecessarily high temperatures. Temperature Protection is most helpful if the atomizer begins
to dry out, the user pauses during a puff, the beginning or end of the puff, or if the wattage setting is
inappropriate for the attached atomizer.
In normal operation, when the device is not firing the maximum temperature setting is
displayed on the screen. When the device is firing, the actual average temperature of the coil is
displayed on the screen.
By default, the Temperature Protection setting is 450° Fahrenheit (232.22° Celsius). To change the limit
1) Lock the device by pressing the Fire button five times.
2) Hold down the UP and DOWN adjust buttons for two seconds.
3) After two seconds, the maximum temperature will be displayed, and the UP and DOWN buttons
should be released.
4) Use the UP and DOWN buttons to adjust the maximum temperature
5) When the display shows the desired maximum temperature, press the Fire button to exit
temperature adjust mode.
The maximum temperature is adjustable between 200° Fahrenheit (93.33° Celsius) and 600° Fahrenheit (315.56° Celsius). To
disable the temperature protection entirely, adjust the limit up to 600 degrees, then press the UP
button one additional time. The temperature limit will read OFF. This will also disable the prompt when
a new atomizer is attached.
Preheat
When the DNA 40 is used with a temperature sensing atomizer, an additional feature called
Preheat is activated. No vapor is produced when the temperature is below the boiling point of the
liquid. Preheat applies extra power until the heating coil is up to operating temperature to shorten the delay between pressing the fire button and generating vapor.
Because the preheat is temperature based, it will not overheat or burn the vapor.
Attaching a New Atomizer
The DNA 40 uses the resistance of the atomizer to calculate the temperature of the heating coil.
It continually looks to see whether a new or changed atomizer has been connected. If you are using
temperature protection, be careful to only attach new atomizers that have cooled to room temperature
to the device. If a new atomizer is attached to the DNA 40 before it has cooled down, the temperature
may read and protect incorrectly until the new atomizer cools.
When you connect a new atomizer or disconnect and reconnect your existing atomizer, the DNA
40 will prompt you to confirm this change. When you fire the first time, before activating the DNA 40
will prompt
“New Coil? UP YES/DOWN NO”. When you see this prompt, if you have attached a new
atomizer, press the UP button. If you have disconnected and reconnected the same atomizer, press the DOWN button.
For manufacturers outside the United States, the DNA 40 is available as a special order with
Celsius units instead of Fahrenheit.
Operation
Basic operation of the DNA 40 is as follows. To wake the device from power off state, tap the
Fire button. To generate vapor, press the Fire button. To change the wattage setting for more or less
vapor, click or hold the Up and Down buttons.
Display
The DNA 40 has a small .69” diagonal blue OLED screen. The screen is attached to the main
board by a flexible cable, allowing freedom in the design of your device. Please use caution when
handling the screen and design the device so that the cable will be secured or strain relieved in
operation. The normal and special operating modes shown on the display are discussed below.
The DNA
40 will automatically detect whether a temperature sensing (Nickel 200) or standard (Kanthal etc) coil is
attached.
Temperature Protected
Watt setting: The power level currently set on the DNA 40.
Battery indicator: The current state of charge of the battery.
Temperature display: When not firing, the maximum heating coil temperature setting. While firing, the
actual temperature of the heating coil is displayed.
Ohms display: The resistance of the atomizer attached to the device. This is measured only when the
unit is supplying power to the atomizer. At other times, it shows the most recent measurement.
Non-temperature Protected
Watt setting: The power level currently set on the DNA 40.
Battery indicator: The current state of charge of the battery.
Volts display: The output voltage being supplied to the atomizer.
Ohms display: The resistance of the atomizer attached to the device. This is measured only when the
unit is supplying power to the atomizer. At other times, it shows the most recent measurement.
Modes
Locked mode: Pressing the fire button five times with less than .7 seconds between presses will cause
the device to enter Locked mode. In Locked mode, the device will not fire and the output power will not
adjust accidentally. While in Locked mode, the screen will be off, except that pressing a button will show
“Locked, Click 5X”. To exit Locked mode, press the fire button 5 times.
Stealth mode: While locked, holding the fire and down buttons simultaneously for five seconds will
switch to stealth mode. In this mode the display is off. It will still show error and lock messages. To
switch back to normal display mode, hold down the fire and down buttons simultaneously for 5 seconds.
This setting is stored to internal flash memory, and remains if power is removed.
Right Mode and Left Mode: While locked, holding the fire and up buttons simultaneously for 5 seconds
flips the display. This allows for maximum flexibility in designing the mod, as well as accommodating left
handed use. This setting is stored to internal flash memory, and remains if power is removed.
Power Locked mode: Holding down both the up and down buttons for two seconds will place the device
in Power Locked mode. In this mode, the mod will operate normally, but you will not be able to change
the power setting. This mode prevents accidental power level changes due to the buttons being pressed
while in a pocket. To exit Power Locked mode, hold the up and down buttons for two seconds.
Max Temperature Adjust: From Locked Mode, holding down both the up and down buttons for two
seconds will place the device in Max Temperature Adjust mode. Once this mode is entered, the max
temperature will be displayed. The up and down buttons are used to adjust the max temperature. To
save the new temperature setting and exit, press the Fire button.
Error Messages
The DNA 40 will indicate a variety of error states.
Check Atomizer: The DNA does not detect an atomizer, the atomizer has shorted out, or the atomizer
resistance is incorrect for the power setting.
Shorted: The atomizer or wiring are short circuited.
Weak Battery: The battery needs to be charged, or a higher rate battery needs to be used. If this
happens, the DNA 40 will continue to fire the atomizer, but will not be able to provide the desired
wattage. The Weak Battery message will continue to flash for a few seconds after the end of puff.
Temperature Protection: The heating coil reached the maximum allowed temperature during the puff.
If this happens, the DNA 40 will continue to fire, but will not be able to provide the desired wattage.
Ohms Too High: The resistance of the atomizer coil is too high for the current wattage setting. If this
happens, the DNA 40 will continue to fire, but will not be able to provide the desired wattage. The Ohms
Too High message will continue to flash for a few seconds after the end of puff.
Ohms Too Low: The resistance of the atomizer coil is too low for the current wattage setting. If this
happens, the DNA 40 will continue to fire, but will not be able to provide the desired wattage. The Ohms
Too Low message will continue to flash for a few seconds after the end of puff.
Too Hot: The DNA 40 has onboard temperature sensing. It will shut down and display this message if the
internal board temperature becomes excessive.
Auto power down
The screen will be at full brightness while firing. After 10 seconds with no button presses, the screen will
dim. 30 seconds after the last button press, the screen will fade out and the device will go into sleep
mode. To wake the device, press the fire button.
External component recommendations
The DNA 40 is a self-contained power regulator which does not require external components for
its user interface. However, it does support the use of external interface components if desired.
Fire button:
Use a momentary on, normally open type switch or button. A standard pushbutton switch is
appropriate. The switch is a logic function – all power switching is handled with transistors inside the
DNA module, so the switch does not need to be rated for power. A waterproof or processed sealed
switch is recommended.
Up/Down buttons:
The small onboard buttons labeled UP and DOWN allow the user to increase or decrease the
power level in .1 Watt increments. The onboard tactile switches are waterproof and rated for 300,000
actuations. However, they are designed to always be used with external actuators, not pressed directly
with the fingers. Please make sure the actuator presses down on the button only, and does not rotate or
drag the top surface. Alternatively, remote normally open type switches or buttons can be attached to
the UP and DOWN mounting holes for customization.
Battery:
A single cell rechargeable lithium chemistry battery is recommended. Either a lithium ion or a
lithium polymer type can be used. Any battery used should be rated for a MINIMUM of 16 amps
continuous discharge current. High C rated lithium polymer or IMR cylindrical cells are strongly
preferred. Make sure that all contacts and connections are capable of handling at least 16 amps.
Charger:
Evolv offers an accessory DNA Charger which is USB powered and provides a 500 milliamp
charge current. Other chargers can also be used. The use on an onboard charger is optional – a
removable battery will also work.
